SC944-05

Scientific Conversions SC944-05

SC944-05LF Top View

SC944-05LF Bottom View

SC944-05 is a handcrafted transformer made by Scientific Conversions. The suffix LF stands for Lead Free.

SC944-05 Waveform

SC944-05 @ 200mv/100ns Div

SC944-05 @ 200mv/50ns Div

SC944-05 @ 200mv/25ns Div

Since the Vpp of the original waveform is around 3.3V, with PE65612 (1:1), I have to use resistors to decrease the output voltage level to 600mV. In the test above, those resistors were not removed, I think that's why the peak will be lower than the second one. If the listening experience is better than PE65612, I'll remove those resistors since they are no longer required due to SC944-05's primary/secondary ratio - 2:1.

PE65612 Waveform

PE65612 @ 200mV 25ns

Obviously, SC944-05 has less noise than PE65612 with nearly the same rise time. However, the jitter is not something we can see directly from the oscilloscope, but I believe that my ears will tell.

Listening and Conclusion

The listening experience of the SC944-05 is all positive, better resolution, more clear and accurate bass and the harmonics compare to PE65612.

I'm pretty sure that I'l never go back to PE65612 definitely!


Note for Usage

The pinout for SC944-05 is almost the same with PE65612, you can replace Pe65612 with SC944-05 directly except for SC944-05 needs an additional hole for its pin 2.

The pin 2 is for "shielding", which connects to the shield between the primary and secondary coils.
Th shielding will greatly improve the noise suppression, hence, except for creating an additional hole for SC944-05 while replacing the PE65612, remember to connect the pin 2 of the SC944-05 to the ground of the primary on transmitter side, and to the secondary ground if used on the digital receiver side.

Updates

After 3 hours running-in, I got new conclusion:

PE 65612 is NOT comparable to SC944-05, they are not at the same level!

DSIX with PO74G04

PO74G04


PO74G04 is an alternative ultra high speed solution for 74HC04, the specification is excellent, supports up to 1.125 GHz bandwidth and the propagation delay is less than 1.4 ns with rise/fall time 0.8 ns.

To me, this is an awesome solution as a replacement for TC74VHCU04.




PO74G04 On the Oscilloscope

PO74G04 @ 100ns/100mV



PO74G04 @ 25ns/100mV


Amazing rise/fall time (compare to the TC74VHCU04 in the following graph).

TC74VHCU04 @ 25ns/200mV


The overshoot and the ringing might be the noise from my power supply, will try to improve this later.

Listening Experience

Noticeable improvement discovered.

1. More silent background, this implies the resolution is greatly improved.
2. More solid bass, even when the bass guitar and the bass drum are played at the same time, you will be able to recognize them respectively.

Conclusion

Highly recommended, what are you waiting for?

Gigabit-Ethernet Optical Transceiver Research

HP/Agilent HFBR-53D5




Recommended Circuit on HFBR-53D5 Datasheet




HFBR-53D5 Circuit in Production




Analysis

R3 68R ---> R201 49R9
R2 68R ---> R200 49R9
R4 ---->
R1 ---->
R11 270R ---> R199 274R
R10 270R ---> R198 274R

Power Requirements

VCC = 4.75 to 5.25 V
Icct = 85mA (typical), 120mA (max)

Optical Characteristics

Transmitter Output Optical Power: -9.5 ~ -4 dBm
Receiver Input Optical Power: -17 dBm ~ 0 dBm

This means we can connect the TX and RX directly without attenuator.

Signal Detection

On datasheet page 10:

If Signal Detect output is not used, leave it open-circtuied.

Signal Input/Output

The HP/Agilent HFBR-53D5 is a PECL based solution.

PECL is differential signaling provides noise cancellation, in the the graph taken from Wikipedia, we can realize how it works:



Vee = GROUND
Vlow = 3.4V
Vhigh = 4.2V
Vcc = 5V

Conclusion

Most of the digital audio source signal is based on TTL, if we are going use the HP/Agilent HFBR-53D5 for the inter-chassis transmission, obviously the TTL needs to be converted to PECL on the TX side and then be converted back to TTL again on the RX side.

Another possible solution will be TTL based optical transceiver which supports 20Mbps or above, however I couldn't find such kind of transceiver.

Possible Solution for TTL/PECL Conversion

Here are some possible solutions :

PO100HSTL179A
TB5D1M/TB5D2H
MC10ELT28

[ To Be Continued ]

Alternative Transmission Consideration for Digital Audio

Just to post some photos of the optical transceiver for high speed network transmission here.

Pulse Transformer on 10/100 BaseTX



Optical Transceiver on OC3/ATM






Optical Transceiver on Gigabit-Ethernet



Optical Transceiver on OC48







XENPAK Optical Transceiver on 10GE



The Question on My Mind

What if we use those solution to replace the TOSLink?
What will happen? Interesting ................

PO74G38072 Digital Buffer

Background

Toshiba TC74VHCU04 is a well-known digital audio buffer chip since it was used in the famous DSIX circuit.
The PO74G38072 designed by Potato Semiconductor is a buffer chip for digital signal, supporting up to 1GHz. PO74G38072 was recommended by some DIYers as a alternative solution for digital buffer than the TC74VHCU04 due to the wide-bandwidth and its perfect specifications. I did a simple test, replacing the TC with PO chip, and the following is my discovery.

Listening difference

It was a surprise to me......... Surprise? So, better or worse?

Unfortunately, after swapping TC74VHCU04 with PO74G38072, my system sounds worse.
Actually, the two chips sounds nearly the same, however TC74VHCU04 provides more silent background than PO74G38072.
As a result, the TC74VHCU04 gives more dynamics in general.

Investigation

I then tried to find out the reason technically.

Here's the comparison of the TC74VHCU04 and Po74G38072 on the oscilloscope:

TC74VHCU04@100ns/200mV


PO74G38072@100ns/200mV


Let's take a closer look:

TC74VHCU04@25ns/200mV


PO74G38072@25ns/100mV


As you can see, TC74VHCU04 has less ringing and overshoot than PO74G38072. In other words, less noise.
I think basically that's why TC74VHCU04 sounds better than PO74G38072 on my system.

Conclusion

I do believe that PO74G38072 should have better performance than TC74VHCU04, since it supports more bandwidth than TC. However, wider bandwidth sometimes means that the noise will passthrough the buffer as well. And I think that is basically why PO sounds worse than TC on my system. (Please note what I'm saying - my system)

But if I can decrease the noise on the power supply, I think there is more chance that the PO might sound better than TC for one reason - less jitter. PO is a much faster chip than TC, if we can well control the noise level sourced from the power supply, I do believe that the less jitter characteristics of the PO chip will be easily identified in this case.

I think the power supply will be the next task for me.